How tall should my canopy be? 19"x11"
Tropical Fish

Tropical Fish Keeping - Aquarium fish care and resources » TFK Resources » DIY Aquarium » How tall should my canopy be? 19"x11"

How tall should my canopy be? 19"x11"

This is a discussion on How tall should my canopy be? 19"x11" within the DIY Aquarium forums, part of the TFK Resources category; --> Hey guys, I'm building an aquarium from scratch, and all that's left is the canopy and the trim around the bottom. I don't have ...

Reply
LinkBack Thread Tools vBmenu Seperating Image Search this Thread vBmenu Seperating Image
How tall should my canopy be? 19"x11"
Old 01-18-2010, 04:40 PM   #1
 
How tall should my canopy be? 19"x11"

Hey guys, I'm building an aquarium from scratch, and all that's left is the canopy and the trim around the bottom. I don't have a lot of experience with aquariums, so I'm having some problems with this last part. If the canopy is 11 inches deep by 19 inches wide, it leaves a 1/8" gap on all sides- this is perfect, I think. I constructed a mock-up out of cardboard, and when I make it 4" tall, it seems too big- but 3.5" seems too short. It's hanging over 1/2", but it still looks a little goofy when I have a 1" overhang.
The tank height is approximately 14.5"

How tall would you guys make your canopy?

Thanks!
Robanada is offline   Reply With Quote
Old 01-18-2010, 04:46 PM   #2
 
Angel079's Avatar
 
Howdy....I just recently built a stand as well for my 55g....What I can tell yea is consider he height of your tank and your own height for maintenance.
Like for me (5'3") and a standard sized 55g a height of 3ft for the stand works wonderful...a height of 37" not so cool....

What I also find helpful, my stand is actually 5" deeper then the tank, which gives me 2" on the back (so it can slide all the way to the wall, but the stand itself can't cause of baseboards) and 3" in the front to set fods, nets yaddy ya on to while I work on the tank.
(You can see pictures of it under my aquarium log "New 55g")
Angel079 is offline   Reply With Quote
Old 01-19-2010, 03:45 PM   #3
 
Cool cool, thanks for the info. I checked out your tank- and I think it's a bit bigger than what I'm working with (a 10 gallon). I was more trying to figure out how big to make the canopy so that it doesn't look like it's proportionally too big or small. It seems like most canopies are 1/3-2/3 the height of the glass, so in my case, I'd be looking at around 5-6 inches. I just don't want it to look comically large, ya know? xD
Robanada is offline   Reply With Quote
Old 01-19-2010, 05:09 PM   #4
 
Angel079's Avatar
 
LOL yea that recent stand was for a 55g
For the 10g (standard sized) I'd maybe make the top board 0.5" larger on the back, left & right and about 2" larger on the front OR make all 4 sides 0.5" only (to lay down stuff while working the tank). 5-6" overhand would bee too much for my taste (or rather my eyes lol).

For the actual height of the stand I'd do 30" (that's what my 10g sits on too); to visually "break" this so it doesn't look like this lil tall skinny stand add one, ideally 2 shelf inside of it and put either decorations or fish supply or both in it.
Angel079 is offline   Reply With Quote
Old 01-20-2010, 12:48 AM   #5
 
Ooh wait- are we talking about the same thing?
It's going to sit on my desk, so I'm not making a stand. I just want to make the part that sits on top and houses the lights, this part.

A 5-6 inch overhang would be too much for me, too! I was suggesting that the vertical height of just the canopy itself would be 5-6 inches, with a 1/2 inch overhang.
Just in case there was any confusion, I threw this together- I apologize for how crude it is, I'm not very good with this sort of thing.

These are the dimensions I was thinking of:




The blue measurement is the one that I'm not sure about, and am looking for suggestions for.
Robanada is offline   Reply With Quote
Old 01-20-2010, 10:43 AM   #6
 
Angel079's Avatar
 
Alright...no we weren't talking bout the same, you want a hood and I talked about a stand lol
For Hood/ Light DIY; I think you'd find the ideas in our DIY thread helpful here adventures in budget DIY lighting Comes with plenty of pictures too.

Yea the hood I'd only cut barley larger then the tank (You can see my DIY Hood in the thread named, post #16)
The height there will directly depend on what lights/ fixtures you'll actually use? Beig a 10g I doubt you use a flourecent strip but rather screw in bulbs right?
Post #28 here has the pictures of the bulbs I use http://www.tropicalfishkeeping.com/f...a-35367/page3/
For it and the fixture I'd do a height of 5" as well. Thou my 10g measures top-bottom where the lights are 3.5"; so 5" sound safe size for a lot bulb sizes to me.

Really make sure what exact lights and fixtures you wanna get FIRST and then built the height based off of it, you don't wanna wind up building it and then realize you're missing 1/8" in the end...
Angel079 is offline   Reply With Quote
Old 01-20-2010, 07:59 PM   #7
 
What is the minimum clearance required for the lights? Work off of that first.
Claudia1002 is offline   Reply With Quote
Old 01-21-2010, 03:19 PM   #8
 
Quote:
Originally Posted by Angel079 View Post
Alright...no we weren't talking bout the same, you want a hood and I talked about a stand lol
For Hood/ Light DIY; I think you'd find the ideas in our DIY thread helpful here adventures in budget DIY lighting Comes with plenty of pictures too.

Yea the hood I'd only cut barley larger then the tank (You can see my DIY Hood in the thread named, post #16)
The height there will directly depend on what lights/ fixtures you'll actually use? Beig a 10g I doubt you use a flourecent strip but rather screw in bulbs right?
Post #28 here has the pictures of the bulbs I use http://www.tropicalfishkeeping.com/f...a-35367/page3/
For it and the fixture I'd do a height of 5" as well. Thou my 10g measures top-bottom where the lights are 3.5"; so 5" sound safe size for a lot bulb sizes to me.

Really make sure what exact lights and fixtures you wanna get FIRST and then built the height based off of it, you don't wanna wind up building it and then realize you're missing 1/8" in the end...
Thanks for the links, and the advice =) I am using screw-in compact fluorescent bulbs (6500K, 550 lumens each, i believe 13 watts? might be 9..)
I've already built the fixture, so all I need to do is bolt it into my hood now- the one I haven't made yet, haha.
I've constructed a full size model out of cardboard just to get a feel for it, and 5" looks about right..I think I'll go with that once I get around to the hardware store. (I live on campus at school and spend all my time studying- i hardly have time to get out and plan the construction! Hah)

Quote:
Originally Posted by Claudia1002 View Post
What is the minimum clearance required for the lights? Work off of that first.
Um, I'm not entirely sure what this means- the bulbs and reflector hang down 2.5" from the top of the canopy. So, if I leave an inch of glass above the top of hte water, with a 1/2" overhang on the canopy, that should give me 3" clearance between the water surface and the edge of the reflector- if I go with a canopy that is 5" tall.
Is that what you meant?
Robanada is offline   Reply With Quote
Old 01-21-2010, 04:04 PM   #9
 
Angel079's Avatar
 
Sounds like a rock solid planning to me there! Thou some picture os the "making" would be nice afterward...if you hadn't noticed with the other links...we LOVE DIY ideas here lol
PS nice choice on lights there, your plants will appreciate it
Angel079 is offline   Reply With Quote
Old 01-21-2010, 04:42 PM   #10
 
Quote:
Originally Posted by Angel079 View Post
Sounds like a rock solid planning to me there! Thou some picture os the "making" would be nice afterward...if you hadn't noticed with the other links...we LOVE DIY ideas here lol
PS nice choice on lights there, your plants will appreciate it
Haha, ok, this is part of a huge project, and I haven't been taking that many pictures, but I'll definitely update this thread when I'm done.

I wanted to ask you about those plants, by the way- I saw your posts in some other threads, and it sounds like you know your stuff!
I don't um..have..any plants... I have fake plants, but I didn't want the challenge of growing plants, since this is my first aquarium since my fishbowls with goldfish as a [younger] kid (10 years ago?).

I'm concerned about algae growth, i was going to get an otto, but apparently I'm supposed to get 5 or more. And, according to aqadvisor, my tank won't support 5 ottos. Plus I've been choosing colors for this tank to contrast with blue fish, hah.

Do you think that I should worry about this?
Not to hijack my own thread or anything xD
Robanada is offline   Reply With Quote
Reply

Similar Threads
Thread Thread Starter Forum Replies Last Post
How about a "show us your custom canopy" contest??? bigdeeezy DIY Aquarium 10 07-02-2010 05:25 PM
Looking for glass canopy to fit a 45gal 36"x12" acquarium anthonyjd81 Beginner Freshwater Aquarium 7 02-27-2010 12:53 AM
what size is 48" wide, 19" deep and 23" tall redlessi Freshwater Aquarium Equipment 3 10-13-2009 09:51 PM
"Meat" coral - how long to "open"? Mike Coral and Reef Creatures 4 04-02-2007 12:03 PM


Thread Tools Search this Thread
Search this Thread:

Advanced Search



All times are GMT -5. The time now is 07:20 AM.