DIY co2 not working?
Tropical Fish

Tropical Fish Keeping - Aquarium fish care and resources » TFK Resources » DIY Aquarium » DIY co2 not working?

DIY co2 not working?

This is a discussion on DIY co2 not working? within the DIY Aquarium forums, part of the TFK Resources category; --> I tried two different rescipes, the one on this site, and the one on this website: http://www.qsl.net/w2wdx/aquaria/diyco2.html The problem is, none of them seem ...

Reply
Old 05-04-2008, 12:34 PM   #1
 
okiemavis's Avatar
 
DIY co2 not working?

I tried two different rescipes, the one on this site, and the one on this website: http://www.qsl.net/w2wdx/aquaria/diyco2.html

The problem is, none of them seem to have produced any co2- I just don't see any bubbles coming out, either when I first set it up, or a few days later. I'm using a glass diffuser that is supposed to work with diy systems, I bought it here: http://cgi.ebay.com/Nano-Co2-diffuse...QQcmdZViewItem

Is that my problem? Is it not letting the co2 through? If so, why isn't my bottle building up more pressure? It doesn't seem to be inflated full of gas or anything. I checked the seal around the cap, and added more glue, but it's definitely not leaking. I'm also using co2 resistant tubing.

I have photos of my entire setup being made here: http://www.fishforum.com/viewtopic.php?t=805

Thank you!!
okiemavis is offline   Reply With Quote
Old 05-04-2008, 06:34 PM   #2
 
blueblue48's Avatar
 
I used that exact setup and everything worked fine, although i didnt use the glass diffusor. you could try taking that off and placing the tube near the intake of your filter, that way it gets cut up into tiny bubbles and spread around the tank. the glass diffusor is the only part of the setup that i think wouldnt work.
blueblue48 is offline   Reply With Quote
Old 05-05-2008, 01:36 PM   #3
 
fish_4_all's Avatar
 
Did you activate the yeast? Soaking the yeast in tepic/luke warm water will activate it so that it doesn't take forever to start producing. Use about 1 cup of water with a little sugar and the yeast. Add the sugar, dissolve it, then add the yeast. When the whole mixture starts to bubble, add it to the bottles.

Also, temperature is important to production. You need to keep the bottles warm, 75-85F to produce enough to make a difference.

The check valves could also be the cause. Remove them for a short period of time to see if CO2 flows into the tank. If it does, bad valves or they are too strong.
fish_4_all is offline   Reply With Quote
Old 05-05-2008, 05:13 PM   #4
 
okiemavis's Avatar
 
I did activate it first- I think the temp may be the problem. I've got a spare heater and I'm going to put the bottle in a bucket with the heater to keep it at an even temp.

I also think you may be correct about the check valve. I'll remove it and see if that helps at all.
okiemavis is offline   Reply With Quote
Old 05-05-2008, 05:17 PM   #5
 
okiemavis's Avatar
 
Sorry for the double post, but whoa, you were so right about the check valve! I pulled out the bit between the tube in the bottle and the tube in the valve and I heard (and smelled) so much co2 rush out! Apparently there was more pressure building up than I had thought.

Thanks a bunch, it never even occurred to me!
okiemavis is offline   Reply With Quote
Old 05-05-2008, 05:22 PM   #6
 
fish_4_all's Avatar
 
Also, if you don't already 2 bottles in the system is a good idea. That way you can swtich one out every other time so the other keeps pumping good amounts of CO2. This helps prevent the CO2 levels from fluctuating too much.
fish_4_all is offline   Reply With Quote
Old 05-05-2008, 05:24 PM   #7
 
okiemavis's Avatar
 
Yep! I've got that set up :D

I must say, I liked the second recipe I tried better. It was much more specific and seemed to be very efficient.
okiemavis is offline   Reply With Quote
Reply

Similar Threads
Thread Thread Starter Forum Replies Last Post
Fin rot... melafix not working studioskim3 Tropical Fish Diseases 1 05-12-2008 12:07 PM


Thread Tools Search this Thread
Search this Thread:

Advanced Search



All times are GMT -5. The time now is 06:30 AM.