crap lol - Tropical Fish Keeping - Aquarium fish care and resources
 
LinkBack Thread Tools
post #1 of 5 Old 06-09-2013, 01:44 AM Thread Starter
New Member
 
crap lol

I recently bought a lot of aquariums off of craigslist.
I tried to drill a hole in the 150, but little did I know it was tempered glass.
Now the whole side panel is cracked, all over, but it didn't shatter LOL
It looks like someone cracked it in one place, then slowly applied pressure to the entire plate, not breaking it, but spreading the cracks LOL
Except it happened all at once
In like 1 second
Halp me
Jorunder is offline  
Sponsored Links
Advertisement
 
post #2 of 5 Old 06-09-2013, 07:22 AM
New Member
 
If on bottom buy thick acrylic piece you can drill it .I would even mount the tank on plywood after the repair drill through both. when they build aquariums on "TANKED" they are mounted on plywood
WvHoopie is offline  
post #3 of 5 Old 06-09-2013, 10:29 AM
You can cut a piece of either tempered or even window glass to fit the entire inside end, leaving the existing glass in place. Put a bead of silicone first, place the glass, then seal it in place. Forget about drilling.

Quote:
Originally Posted by Jorunder View Post
I recently bought a lot of aquariums off of craigslist.
I tried to drill a hole in the 150, but little did I know it was tempered glass.
Now the whole side panel is cracked, all over, but it didn't shatter LOL
It looks like someone cracked it in one place, then slowly applied pressure to the entire plate, not breaking it, but spreading the cracks LOL
Except it happened all at once
In like 1 second
Halp me

Father Knows Best but Abbey knows everything! I once knew everything, then I asked one question.
` ...><((((>` . . ` . . . ><((((> . ` .. . ><((((>
AbbeysDad is offline  
post #4 of 5 Old 06-09-2013, 02:13 PM
Window glass would probably work for a smaller tank, but not for a 150. Plate glass at 3/16" is about as thick as it gets for windows. I go to ace hardware to get window glass cut for tank lids and it is thinner then your typical glass top to the point where the glass sags on my 3 ft tank. The glass they sell is thinner 1/8" I think. Getting a replacement piece of glass for the 150 you will have to go to a specific store for glass that can do custom orders, but its not likely going to be cheap for a large piece of thick glass. If you want to replace it with non-tempered you need to look into the thickness it should be. Non-tempered will likely have to be thicker then what the tempered sheet was, since tempered glass is much stronger. Then there is the work of removing the bottom and top trim(hopefully not damaging the other panes) then removing the broken pane and putting the new one in. Then the issue if the trim would fit back on if the replacement pane was thicker. Trim is very important for tempered glass as it is actually weak to impacts on the edges then typical glass. Once you break a pane there is no fixing it.

You could try to fix it using plywood but, I have very little knowledge of how this is done.

If the side pane is tempered the entire tank will be. Its a lesson learned the hard way but you should always check for tempered glass whenever drilling a large tank. Above 55 gallons tempered glass is pretty common. My first 55 gallon tank was fully tempered according to the sticker. I replaced it after 7 years when the brace started giving out and the new 55 is non-tempered with noticeably thicker glass. There are plenty of videos on Youtube of how to identify tempered glass, it involves a LCD/LED screen(cellphone usually these are polarized) and another polarized filter(camera or sunglasses). Make sure you check both side and bottom panes. Some tanks can have all panes tempered, some only the bottom pane, and other will not be tempered at all.

.... I'm probably drunk.

This is how I lurk


Mikaila31 is offline  
post #5 of 5 Old 06-11-2013, 10:31 PM
Bear in mind that I was referring to placing glass directly over the existing cracked glass, not replacing it. Of course if the glass is being replaced, tempered glass of the appropriate thickness is required...however, without framing this can be difficult to get right.


Edit: come to think of it, I might silicone in a piece of acrylic on top of/over the existing side wall glass.

Father Knows Best but Abbey knows everything! I once knew everything, then I asked one question.
` ...><((((>` . . ` . . . ><((((> . ` .. . ><((((>

Last edited by AbbeysDad; 06-12-2013 at 08:09 AM.
AbbeysDad is offline  
Reply

Thread Tools
Show Printable Version Show Printable Version
Email this Page Email this Page



Similar Threads
Thread Thread Starter Forum Replies Last Post
ohh crap... David007c Beginner Freshwater Aquarium 6 09-02-2010 11:22 PM
Oh crap. Davidb86 Catfish 5 03-02-2007 03:04 AM

Posting Rules  
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

 
For the best viewing experience please update your browser to Google Chrome